I2C display not working ver .91 (no replies)
Hi, I have constructed a clone of VIKI (Adafruit RGB LCD shield based) from circuit diagrams and attached it to Azteeg X1 board. I tested the display with the 'Hello World' sketch from Adafruit and it...
View Articlefeedrate problem (no replies)
I hope that someone has the answer to my question because my friend google left me...... I made a 3d printer using the following configuration: nema17 steppers, aduino/ramps1.4 with pololu drivers and...
View ArticleRepetier Host layer numbering (no replies)
Is it correct that Repetier Host is counting from Layer 0 and the first layer is 0 when a Z layer setting is met? However if Slic3r or other slicers has some custom g-code including positioning, it...
View ArticleRepetier Server + BeagleBone Black + Logitech 920 HD camera? (no replies)
Hi, I have some questions about Repetier Server: 1. Does it support BeagleBone Black? 2. Have you considered adding webcam support to stream live video from the printer? (Logitech 920 do internal HD...
View ArticleRepetier firmware/host stopping midprint (no replies)
Hi guys, I'm having some awkward printing issues lately. The following are the settings: H-Bot config Azteeg X3 board. See config file for more info. I'm using repetier 0.83 firmware with repetier...
View ArticleGraphics freeze when zooming during print (no replies)
Has the same problem again, but this time with v95E. Was printing and frame rate was about 600FPS. Did a few zoom in while printing and graphics was freezing and could not recover. Repetier Host v95E...
View Articlem340 servo sends z0 in eprom (no replies)
Im having a little problem with servo control, Firmware version 0.91 rev 4 host 0.95f If i send script M340 P1 S500 i get "20:49:34.184 : Printer height:0.01" basicaly i sets whtever height im at to...
View ArticleConnection issues :S (1 reply)
Hi, everyone. I seem to be having some sort of connection issues. I am using arduino mega / ramps 1.4 and i recently switched to the newer version of RepetierHost (0.95F) The trouble is that my...
View ArticleMac host v0.56 freezing at startup? (4 replies)
Hi all. For the last few months I'd been printing flawlessly on my mac with version 0.56. Suddenly though, the program has started freezing as soon as I open it. I hadn't changed/added/deleted...
View ArticleRepetier 0.91, Arduino Due and RAMPS-FD (1 reply)
Does the current ARM version of repetier 0.91 support the RAMPS-FD boards for the Arduino Due? In the firmware config I only see these options. RAMPS-FD-> ( [www.geeetech.com] ) I know what RADDS...
View ArticleI need Firmware for Irapid Black (2 replies)
I need the Irapid Black Firmware. I did a mistake and flashed my Irapid Black with the cura Firmware. Can anybody help me? Has anybody the settings so i can flash it myself? I guess it is repetier...
View ArticleZ not moving during print (3 replies)
Hi all, I'm sorry to crosspost this, but I'm trying to get as much insight as possible. I started a thread on the Mendel90 subforum, my problem is basically what the thread title says. Please refer to...
View ArticleRepetier Firmware backlash compensation issue? (2 replies)
Hi All, I was trying to setup the backlash compensation through the "Repetier-Firmware configuration tool for version 0.91 Rev 4" website on my Delta printer. So I was using the manual control in the...
View ArticleRamps 1.4 - EEPROM or HeatBed but not both (no replies)
Looking for some direction for troubleshooting an odd issue. Using the web configurator for .91 I've generated a config for my machine. I've ran into a snag where I can either have the EEPROM enabled...
View ArticleInitial Calibration (no replies)
Hi, I'm currently building a mini Kossel. I have installed repetier firmware .91 and repetier host. I don't have a hotend on the effector yet, I have a QTip extruding down :D Trying not to break...
View ArticleDiagonal movement problem (no replies)
Hi, I've got problem with my rostock printer. When I try to move from position X85 Y85 to X-85 Y-85 (or X-85 Y85 to X85 Y-85) my printer makes something starange. It looks like it blocks and couldn't...
View ArticleRumba Thermistor naming/pins (no replies)
Hi, switching to Repetier I noticed that the naming of the Thermistors in pins.h and on the board are inconsistent. It seems to me (and I tried it) that these settings are correct: #define TEMP_0_PIN...
View ArticleEndstops being ignored (1 reply)
I have a ramps 1.4 board on arduino mega, latest repetier firmware, and mechanical end stops. I am having no issues with anything but endstops so far. Manual control of steppers and heaters is great....
View ArticleProblems with Endswitches (Azteeg x3) (no replies)
Hi there, First my setup: -Ordbot Hardon -Azteeg X3 -Bulldog XL Extruder -Merlin Hotend -Repetier I set up my new 3D printer and have problems with my Endswitches.The Z-Axis works complete but the X...
View ArticleX11 errors and crashes on startup (linux) (2 replies)
I am running repetier Host on Lubuntu (latest version) with everything up to date and everything installed. Upon attempting to start repetierHost, I revieve a huge pile of errors all starting with...
View Article