Help with Repetier FW and BLTouch (1 reply)
I cannot for the life of me get the BLTouch to work with this firmware (1.0.2). i am running a Folgertech FT-5 with MKS 1.4 board. i have tried every possible combination of stuff. i loaded a copy of...
View ArticleOpiliones 3D printer (no replies)
Hello, So a week or so ago i got myself a opiliones 3D printer. Very cheap because the firmware was not on de board yet. So i wanted to do this myself but i get stuck. The firmware marlin i put on the...
View ArticleProblem Connecting Repetier Host to Printer (2 replies)
Windows 10 Downloaded Repetier Host for the first time ~ 12/2/2018. Problem - repeteir server was running and needed to be deactivated in the browser and repetier host. With help from the...
View ArticlePrinter information out put (no replies)
Repetier firmware information read on pc? da vinci id information TO FOOL da vinci software to think that is the original firmware on the printer so that ONE can reinstall original firmware for shop...
View ArticleControl what set of commands go to each driver? (no replies)
For a CNC project I want to use two motors for the x-axis and two motors for the y-axis. However, due to current limits, I would like to have one driver per motor. This would require having, for...
View ArticleM109 (set temp and wait) in G-Code but not in config (no replies)
I've been using Repetier Host and Slic3r for perhaps 5 years. For one set of configurations, the printer waits at the start of a print for the extruder temperature to be reached. This is no big deal...
View ArticleRepetier and Z offset (no replies)
I think this is a Repetier issue: There is a difference between a STEP and a GOTO when dealing with Zhome+offset. Looks like a Repetier issue: => it is not handling a Z offset properly. I have a...
View ArticleWanted: constant movement during linear movement with G1 and G0 sequences (no...
Hello, I'm currently working on my laser cutter based on the repetier firmware (tried 0.9.1 and 1.0.x). Cutting ist (mostly) working perfektly, but now I'm trying to engrave. For this, I'm exporting...
View ArticleG32 Fatal Error & M999 (no replies)
I've searched the internet and can't find any information on my issue. My printers piezo Z probe and bed leveling have been working fine. The printer sat unused for a month. When I started Rep Host I...
View ArticleRepetier Host choking on GCODE when Pronterface doesn't (2 replies)
Hi, I'm having fun with my homemade pen plotter, but sometimes the GCODE that is generated chokes out my Repetier Host. The software runs fine but the prints just stop halfway at a specific piece of...
View ArticleKompilier Fehler bei Repetier für Arduino due (1 reply)
Ich versuche jetzt schon eine ganze weile Repetier auf meinem Sparkcube 1.1XL zu istallieren ich habe Arduino Due RADDS 1.6 xy Core Bauweise xyz MAX endschalter 2 motoren xy achse auf x und y...
View ArticlePark head issue (no replies)
When I trigger P park head script it goes to the XY park position THEN to the Z position. Not good. It should first go to the Z position relative, not absolute, then the XY position. Either that or...
View ArticleRH Scripts skewed (no replies)
I have this problem and just did a clean install (registry, appdata, everything cleaned out) of RH 2.1.6 == I still have the problem. I configured Scripts 1-5 When I hover over them in Manual Control...
View ArticleDelete saved auto level mesh? (1 reply)
Is there a Gcode command or setting in EEPROM to remove the saved mesh? I would like to switch back to manual leveling while I wait for a new probe, without having to flash a new firmware without auto...
View ArticleMotors keep engaged. (no replies)
I am printing with repeater Host. After the last upgrade of it, the motors keep engaged after movements. It used to work like this: In manual control I home the extruder. After that I can still move...
View Articlethermistor errors (2 replies)
I am having a problem with my printer after replacing the Arduino mega board. Downloaded the German RepRap Protos V3 firmware all looked good but the thermistors for the heated bed and the extruder...
View ArticleAzteeg X3 Pro Core XY 8825 lose steps after a few commands. (no replies)
I have tried for 2 days to get this machine to stop losing steps. I have the 8825s set at 1/16 I can move X with a few commands after about 200mm movement it starts losing steps. [youtu.be] Thanks for...
View ArticleHow to stop print, after gcode start? (no replies)
I have a problem with my Repetier. I use it to insert a gcode. It is: G28 G26 C H200 P5 R25 Q4.2 Z4 after i send it to the printer, it starts and print a little example. how can i cancel it? Stop the...
View ArticleProblem With Z Home With Replacement Firmware (no replies)
I am having a problem with my 1.1.9 firmware. When I have AUTO_BED_LEVELING_BILINEAR enabled the printer homes Z in the wrong direction - the nozzle goes up instead of down when I issue G28. With...
View ArticleZ axis won't home or move down (1 reply)
I recently built a 3D printer using a RAMBO board and got it working with Repetier (I found this to be better than Marlin). All axes were moving normally until I adjusted the steps per mm through...
View ArticlePre-heating the extruder and bed will crash with DEF error (no replies)
I do not set temp in the code, so I will manual heat the extruder in repeater host and the bed to the desired temp. When reached, I will start the print. The last time, often I walk away from the pre...
View ArticleCooling fan not activating (no replies)
On repetier host, when I click the fan icon, it appears to turn the fan on, but I’m not seeing any voltage from pin 9. Is this something that isn’t enabled by default, or something I might have...
View Articleis this marlin or Repetier (no replies)
I posted this on the Marlin github [github.com] The question is where is the problem, Marlin or Repetier Host.
View ArticleHow to install Repetier on iMac? (no replies)
Hi Hope you are able to help! I've need to wipe my iMac and re-install appllications, however I am unable to install Repetier-Host! I've downloaded the latest version and tryied and install and it...
View ArticleBL Touch not homing (no replies)
I finally got my BL Touch installed and working with my Rambo 1.3L controller. All commands listed on the instructions work, The only modification I had to make to them was to change M340 PO S700 to...
View ArticleRH opening Slic3r in another window (no replies)
On my laptop, when I click slice with slic3r, it just does it. On my desktop, when I do that, it opens the slic3r console window and slic3r changes the slic3r_settings.ini file back to default. I...
View ArticleMKS-Gen-L -- cannot find it on the Configuration List (2 replies)
Hi, I have not used Repetier for many years and it is time to return. Marlin is outa-control, it may have bricked my Gen-L board. I started with the Repetier web-page Configuration Tool but cannot...
View ArticleAutopoziomowanie (no replies)
Witam! Podłączyłem indukcyjny czujnik zbliżeniowy LJ12A3-2-Z/AX 2mm 6-36V żeby automatycznie poziomować stół i mam problem. Nie mogę sobie poradzić z jego poprawnym działaniem ponieważ po wpisaniu w...
View ArticleUnable to flash Repetier firmware to RUMBA (no replies)
I used the configurator and downloaded the zip for 1.0.5dev. I'm running the Arduino IDE 2.2.1. I've even forced Windows 10 to install the RUMBA board driver. To clarify, this is the OLD RUMBA board,...
View ArticleSending printjob from OrcaSlicer not possible (no replies)
(copy from less frequented Repetier-forum) I searched the internet yesterday and today but unfortunately didn't find a solution... When I try to send a print job to the server from OrcaSlicer (1.9.0),...
View Article