Repetier & Pick and Place Machine (2 replies)
Hi, I have been using Repetier host to test a pick and place machine built using common parts from 3d printers. I tried Repetier firmware but for some reason the z axis shifts unexpectedly so I am...
View Articlecan see 3d anymore (6 replies)
whoops : CAN'T see 3d anymore ===== hi all, i done't seem to be able to see my 3d model on the attached screen anymore (last week or so). and the three radio buttons don;t appear like they are shown...
View Articlerepetier 0.51 not printing from SD card (1 reply)
I'm using repetier 0.51 with marlin 1.0.0 RC2 on a Prusa. I try to run my file on the SD card and I get < 2:44:37 PM: Begin file list < 2:44:37 PM: /TRASHE~1/501/BOBBIN~1.GCO < 2:44:37 PM:...
View Articleget better EXT0_STEPS_PER_MM value (3 replies)
Hi. i'm trying to get better extruder calibration, but the changes i do on firmware (customizing EXT0_STEPS_PER_MM value on configuration.h) do nothing. Just now, when i open host software and execute...
View ArticleUbuntu usb connection fail (2 replies)
I can't connect the usb port on an Ubuntu machine to a Sanguinololu board. The button become green and change fron connect to disconnect but the commands are in queue waiting. Claudio
View ArticleRepetier 0.80 and matrix keyboards (4 replies)
Checked out the dev branch yesterday and gave it a spin with a membrane matrix keyboard hooked up (one of these: [i01.i.aliimg.com]). It's... not quite working. It takes quite a lot of keypresses to...
View ArticleUpdate from .80 to .82 (2 replies)
I just built my first RepRap (Prusa). I got it working with Repetier and after 2 days my hot end Peek melted :-( . Anyway, my replacement parts come in tomorrow and I hope to be printing again. I just...
View ArticleA few OPS questions (9 replies)
I've had some not-quite-good experiences with Repetier-fw's OPS and decided to go back to Slic3r's retract while i figure out what i'm doing wrong... Question #1: With OPS on, fast mode, set to start...
View ArticleX axis travel issue. (4 replies)
First off, I absolutely love the repetier firmware and host, it has transformed my printer into a wonderfull machine! But, I do have one issue left. Sometimes the X drive skips steps when going...
View ArticleCom Port Issue (1 reply)
Hi I hope I'm posting this in the right forum. When I first installed Repetier I was using com 7. I don't remember when or why but after an update to a newer version com 7 disappeared and I had to...
View ArticleRepetier host print time estimation (3 replies)
I love using Repetier Host. The one thing that does not work right is the printing time estimate. I understand it would be very hard to get very accurate but it's so far off it might as well not be...
View ArticleZ Limit Switch Issue (2 replies)
I have a weird issue with Repetier .80. It appears to be read the Z limit as triggered whenever the first extruder heater is on. I am using the Azteeg X3 which wires exactly like a RAMPS. If I home on...
View Article3D View Goes Bad (2 replies)
I need help. It doesn't matter what I print the 3D view eventually goes bad and stops updating. The print runs fine, just the 3D view in Repetier host 0.82b appears bad. I've tried all the...
View ArticleCrash when loading file on linux. (2 replies)
This is on a linux ubuntu 32 bits system, I installed mono-devel package and executed configureFirst.sh. Whenever I try to load a file (I tried STL and GCODE files) repetier crashes. Any pointer about...
View ArticleConnection Errors Repetier FW + Host (36 replies)
Hello RepRap Community! i have built my first RepRap Prusa with Sanguinololu Electronics and installed the Repetier Firmware onto it. My problem is, that sometimes i am able to move my axes for some...
View ArticleCalling Slic3r from Repetier Host (9 replies)
Hi, I'm sure this is answered somewhere - I just can't seem to find it. I'm running a Mac and have downloaded the latest versions of Host and Slic3r. I'm just trying this combination for the first...
View ArticleUnresponsive and stops halfway (2 replies)
Hi there! Just got my new printer and was tinkering around with the software/hardware and encountered a few problems that stumped me and would like to seek some advice from everyone here. I am using a...
View ArticleRepetier Prints Stopping (6 replies)
I upgrade to the new repetier, and now I get random communication drops to the arduino. The arduino is still cycling the heaters for the hot bed and keeping the extruder hot, but it completely stops...
View ArticleCustom Buttons ? Script info (5 replies)
Hi, I believe I saw an answer to my wish before. I'd really like custom buttons (a little like pronterface) that I could configure for head positioning whilst bed-levelling. I don't believe Host...
View ArticleSliced object at different location from placement (3 replies)
I'm using repetier host v0.80 with slic3r v0.9.6. I place objects at a specific location but after slicing they are at the center. How can I prevent this from happening. See attached images.
View Article
