How stop the Gcode (@pause like) from firmware? (no replies)
Hi, How can I stop the Gcode reading from firmware command but maintein the printer connected (temperature reading etc..) exacly as a @Pause command? I already try...
View ArticleDELETING A PRINTER (2 replies)
WHEN ADDING A NEW PRINTER TO THE PRINTER SETTINGS ON THE REPETIER-HOST INSTALLED ON MY IMAC, I MADE A MISTAKE ON ONE OF THE PRINTER'S NAME, AND SO, I WANT TO DELETE IT. HOWEVER, EVEN SELECTING THE...
View ArticleCase Light Pin (no replies)
Once activated in the online configurator pin 41 of the light repetier host does not accept the command M42 P41 S255 M42 to pin 40 Fan Board works Perfect be a new update ?? thanks
View Articleheated bed decoupling repetier 92.3 (2 replies)
ok, I have a cut of repetier work092 extended by 3dArtists for the alligator board. From what I've seen it looks and works great! I've been able to get just about everything running without a...
View ArticleResume after Pause (no replies)
I fried my Gen6. I have rebuilt my Orca v4.x to run on Arduino Mega + Ramps, with Repeiter firmware. I Slice with Slicer and I print with Repetier Host. Al works fine after loads of finetuning....
View ArticleJust out of curiosity (1 reply)
I made a printer that works just fine. Setup is "scavenged/homemade" hardware, controled by a megatronics V2 with marlin and repetier. Evrything is great except that when I do a homing or start a...
View ArticleCompiled RepetierHost 0.90C dont work with Arduino Due native USB (no replies)
Hi, I just compiled the old version of Repetier 0.90c (c#), and I'm not able to connect with Arduino Due USB native port, (note that with programming port it work fine), I even try to deactivate the...
View ArticleTime laps prediction "per layer" (Feature Request) (3 replies)
This is a request that would make my life better :-) Modify the log record that displays the current layer to include an elapse prediction for that layer. Maybe on the LCD too.... Already Reptier...
View ArticleWeb configurator for Repetier FW error? (1 reply)
Trying to get Repeiter FW to work on my delta... After going through the online configurator for 0.92.x, I get the attached configuration.h file. It complies and when loaded and run, the Z motor (the...
View Articlelive preview stops updating. (2 replies)
After some hours, the live preview stops updating. Anyone knows how to solve this? It becomes transparent. [attachment 55164 livejpg.jpg]
View Articlehow to control multi printers with Reptetier (no replies)
I want to control two printers at the same time. However, i did not see add button on Printer setting page.
View ArticleShifting Window Layout (Extend Tabbed Frame) (no replies)
Is it possible to shorten the width of the console frame to allow the tabbed frame (loading files, slicing, manual control, etc...) to extend all the way to the bottom of the screen? There are times...
View ArticleDisplay Z calibration (no replies)
with the new update changed Z calibration missing a voice "Z Position" Display1 Display2
View ArticleArduino/Ramps 1.4 91 or 92 Wont Compile (1 reply)
ok...so i went through the web configurator and downloaded both versions and neither will compile on Arduino 1.6.4 It doesnt fail either. it just sits there forever "compiling sketch" what am i missing?
View Articleupload wrong firmware, board alarm (no replies)
I uploaded incorrect firmware to Ramps 1.4 control board. Now, there is no screen display and it alarms "beep"..
View ArticleMendel90 + Mac + Repetier - 5 Commands Waiting (no replies)
Hello, I recently got my mendel90 set up and successfully test printed. I was using pronterface on an old PC I had and i successfully exectured the test print. However when I went to try and print an...
View ArticleLarge gcode file (no replies)
Using Slic3r, the Repetier generated a quite large gcode file that took almost 6 minutes to be ready. However, a few seconds after recording the gcode on its defaut directory, the Repetier closes...
View ArticleRepetier Server API logs me out immediately (no replies)
Hey there, I am trying to use the Repetier Server API for a project. When logging in, the server logs me out immediately: > {"action": "login", "callback_id": 2, "data": {"rememberMe": true,...
View ArticleThermistor values right? (no replies)
I've just migrated from Marlin to Repetier FW. One thing I've noticed is that the reported temperature seems off by about 20C. In Marlin, I specified EPCOS 100K (Marlin type 1) in configuration.h and...
View ArticleStrange Z Axis Behavior (2 replies)
Hello all, I finally got around to finishing a Mendel I had started several years ago and am very close to a first test print. I am using a RAMPS 1.4 Board with Arduino 2560. I am using Repetier...
View Article