Feeder issues (5 replies)
Hello, I can really use some help. I am currently using what I believe is is Bowden extrude but I am having issues with it. It appears to be trying to feed too fast and will push the filament out of...
View Articlerunning multiple extruders simultaneously for filament blending. (no replies)
I wanted to know if the repetier firmware and repetier host supports sending extrusion codes to multiple extruders simultaneously. not just codes to each extruder but be able to have all 3 divide up...
View ArticleCura Engine Spiral Vase settings in Repetier - can't find (no replies)
Hi I am very new in the field of 3D printing and recently got a OrdBot. I am using Cura for slicing in Repetier and can't seem to find the continuous spiral vase printing option like the Cura...
View ArticleHow to run fans with rumba board? (2 replies)
Hello. After day of experements I surrender. [reprap.org] How to run fan0/1 by m106 m42 with repetier 0.91 firmware? I know fan0 pin7 fan1 pin8 In firmware web setup I checked [www.repetier.com]...
View ArticleTwo different extruder -> two maxtemps ? (2 replies)
Let's say that one user has a bi-extruder machine, one extruder with PTFE insider and one extruder completely metal. The first one must be limited to 255°C to avoid Teflon melting, while the other one...
View ArticlePrusa i3, just installed E3D Cyclops hotend (dual mixing extruder). Can't...
So here's my basic setup: Pretty standard Prusa i3. It's a dual bowden that I designed for the extruder setup. [www.thingiverse.com] I enabled a heated bed in firmware but no heated bed is shown in...
View ArticleCan not control with Repetier, but Cura ok. (1 reply)
I have two 3D printers. I used to control both with repetier, and they work well. Recently, I upgraded firmware (marlin) for one of them. After that, the newly upgraded machine can not be controlled...
View ArticleAuto Bed Trimming / Leveling help!! (with pics and config) (no replies)
I am having some trouble getting my induction probe to auto bed level. I have an ord-bot (http://imgur.com/XlZK44I) with the following settings in Simplify 3d (http://imgur.com/3MIuORi). And my marlin...
View Articleslic3r custom gcode - turn on fan as FIRST action? (1 reply)
Hi all - I am using Repetier/slic3r, and have an E3D hotend with fan that I am controlling. I want to turn on the E3D fan right away *before* the hotend is enabled. There is a section for custom gcode...
View ArticlePT100 sensor (no replies)
You can configure this sensor instead of thermocouple/thermistor? PT100 thanks
View ArticleClik here to view.
Drastic Print Time Difference - Repetier Cura vs Standalone Cura (2 replies)
When I try to slice the same STL file with Cura built in Repetier Host and the standalone Cura - there is a substantial difference between the print time. For the same settings Standalone Cura shows...
View ArticleOffset for Temp Sensor (2 replies)
Hi, my temperature sensor under the glass plate at the headet bed measures always 17 degree more than the glass plate have at the surface. So I need a way for a temperature offset, best in the EEPROM....
View ArticleSlow stop function (1 reply)
Hi! I would like to speed up stop function in my device. It takes about 20 seconds, according to my gcode. This is very annoying I lose time and more filament. Is the possibility to do it immediately?...
View ArticleSeveral Questions (no replies)
I had several questions on how to configure Repetier firmware and where to plug in the trigger on the ramps 1.4 board for laser engraving and triggering the laser. As well as Repetier Host working...
View ArticleSudden Temperture Drop While Printing (no replies)
Greetings! I have the strangest problem with which I need some help. I have been trying to print this Pico fan shroud form Thingiverse (Shorter 30mm Fan Shroud for Pico Hot End) and here is what...
View ArticleRepetier Firmware, M106 Fan command, and Laser Diode Question (1 reply)
Hello, I am using the 0.92 version of the Firmware on a Prusa I3 DIY Kit. I have connected a laser diode (from J Tech Photonics) to D8 on the Ramps 1.4 board. To control the laser I am using M106 Sxxx...
View ArticleRepetier Live CD (1 reply)
Is a LIVE CD of Linux including the Repetier Software avaliable? Unfortunately I run into all kinds of problems setting up the software on my cumputer. It would be handy to have a "install and use"...
View ArticleRepetier Host not communicating with printer (1 reply)
After I finally got a new board, and flashed my old firmware onto my kossel mini, repetier host does not seem to be controlling my printer at all. I have double checked the baud rate, as well as...
View ArticleRepeater host problem with scripts/gcodes (1 reply)
I am a new user and just connected Repetier host MAC to my new Prusa i3. How do I create scripts. My scripts are greyed out on the pulldown menu? Gcodes entered manually are ignored by printer. Why?...
View ArticleRepetier Host where are the configfile? (4 replies)
Can anyone tell me in which file repeatier Host the settings for example Print area stores. I want to copy this file! many Greetings Wolfgang
View Article