Parameters to enter for makerbot replicator 2x (1 reply)
Hello everybody, Do any of you managed to send 3D parts from Repetier-host software to the makerbot replicator 2X USB connection? After completing all the settings, I never get to communicate with it....
View ArticleAutoleveling with a CoreXY-Setup (no replies)
Hi, i'm trying to get the Autobedleveling on a CoreXY-Setup to work but it doesn't quite work as expected. Hardware: Radds V1 X Max, Y Max Endstops Inductive Probe at Z Min Homing via 'G28 X0 Y0' and...
View ArticleRepetier hoost speed controllers (1 reply)
I am switching from Pronterface to Repetier Host. Now ì notice that there are 2 speed controllers that can be adjusted during print. One for movement and one for flow. Are they connected ? If I...
View ArticleRepetier Host and AzteegX5/Smoothie (2 replies)
I'm not sure at the exact moment it happened, however, 1.05 is not connecting to Smoothie on Windows 8.1 (and Windows 10) 0.9 works fine 0.95 works fine 1.05 recognizes that it's there, and will give...
View ArticleNew version unstable? (1 reply)
Had a few prints fail using repetier since updating. It will be printing fine and then stop. Happened after an hour on one, two hours on another. Switched to pronterface and completed a print. Not...
View ArticleFirst 3D printer build suggestions (no replies)
Hello, I'll be building my first printer based on coreXY, the arduino uno 328p and teacup firmware. Here's my connections that I planned: 0 Rx serial 1 Tx serial 2 X Axis Stepper Direction 3 ~ Y Axis...
View ArticleRepetier Host and DUE Board (2 replies)
I have just purchased a Due board managed to upload Repetier v0.92 Firmware to it using the Programming port. However I can't get it to talk to Repetier host (Either 0.95 or 1.05) I have set the reset...
View Articlei2c for other purposes (2 replies)
Hello! I am using repetier on a rambo and want to use the i2c capabilities for communicating with another Arduino. I uploaded an example sketch to the rambo and another arduino and have them talking...
View ArticleObject does not show in Host (5 replies)
I was used to Ponterface and I liked the toolhead path simulation on the screen, while printing. Now I have moved to Repetier Host, but probably I make some errors, because: I do not see the objects I...
View ArticleDelta autolevel creating curvature problems (no replies)
I have a delta printer set up witha capacitive z-probe and glass bed. I've previously had the printer running without a z-probe but got tired of reconfiguring the endstop offsets after each print to...
View ArticleMax temperature 226-228 (no replies)
After rebuilding my Orca with Arduino/Ramps (I fried my Gen6) I can't get the temp higher than 226 - 228 degrees. It heats up at 100% until 226, than it goes to zero power, shoots over to 228 after...
View ArticleUpload to SD card (RAMPS) (no replies)
Hi, does this feature usually work? I have the latest version on Windows, a RAMPS 1.3 board, it can see the files on the SD card already, mount and dismount seem to work, but uploading doesn't. It...
View ArticleRepetier-Host configuration - what is Z length? (1 reply)
Hello, i am trying to configure the repetier-host firmware for my delta printer I am using this wizard: [www.repetier.com] So what is the Z length? It is meaning these static plate from floor to...
View ArticleStrange artifact in brim/skirt (2 replies)
Hi, Does anyone know why i'm getting this strange artifact in the skirt brim of any object I slice? It's like there is an extra object there but there isn't! Not a big problem usually but very large...
View ArticleWall separated from top (no replies)
I've just converted my DaVinci to repetier, and have things mostly adjusted to work properly. However, I'm getting issues with walls not connecting to the top. Here's an example: [attachment 42448...
View Articlecura engine tips (1 reply)
after installing the new ver. 1.0.6 I can not find the suggestions in the box digit CuraEngine
View ArticleMy printrbot simple, made a printing in mirror mode, why? (no replies)
Hi!, when i print a dice with numbers or a names, the prints this things are made in a mirror mode, so how can I fix it? thanks in advance G.
View ArticleWhat do the colours mean? (pic attached) (2 replies)
The eyes have gone red on this model, it's the tree frog, what does this indicate? I was printing at .3mm layer height on a .4mm nozzle. Thanks Ian [attachment 42637 frog2.jpg]
View ArticleSerial Monitor in wait loop (1 reply)
Help please I had PRotos firmware and everything was doing great, then I updated to Repetier and did everything like in the manual. Problem is that now when I upload the firmware it uploads...
View ArticleWhere did flow rate go?? (no replies)
Upgraded to the latest version a day or two ago, where did flow rate go?? [attachment 42730 repetier.png]
View Article