Repetier Host on ODROID-U3? (no replies)
Hi guys, I'm looking for a very low-cost pc solution for running Repetier and Slic3r, Mono and Arduino IDE (under lubuntu) and I'm planning to buy an ODROID-U3 to interact with my handmade delta...
View ArticleExtruder retraction to pick off the filament (no replies)
Hi all, I'm new on the forum and also with the reprap experience! I'm building a customized 3dprint, using ramps 1.4 board and repetier firmware on Arduino mega 2560. All is quite ok but I faced some...
View ArticleCan't find the progress back (1 reply)
hello, (sorry for my english) I accedently deleted the bar under the 3D immage with repetier. i mean the square were it tells you what's it doing... and i can't find a way to bgring it back? can you...
View ArticleFirst Layer Extrusion width (no replies)
Hi, Are there any plans to add support for changing the first layer extrusion width using CuraEngine? This was recently added to Cura itself and can help give a really good first layer adhesion and...
View ArticleZ-probe changes state but smashes nozzle into bed anyway (no replies)
I have a z probe set up on a large delta printer to compensate for errors coming from when I remove the print bed for removing parts/cleaning. I'm running repetier .91 in host 1.0.1. When I send G31...
View Articlecura.ini: No key value pair found (no replies)
Here is a bug in Repetier Host 1.0.4. With the default Cura settings, the CuraEngine CLI fails to parse the cura.ini file. See the log: 00:45:21.570 : CuraEngine command:C:\Program...
View ArticleDisable temp check on a per-extruder basis (2 replies)
Hi, I've designed and built a chocolate extruder for my printer, and have hit on a small snag. I'm not using a heater at all, instead just putting warmed chocolate inside an insulated syringe. This...
View Articlebed temperature slider not working in repetier v103 (no replies)
Hello, after connecting a 160mm heated bed on my kossel mini the temp.slider is not responding. Tempsensor is working (tested with cup hot coffee on bed and with ice ) When temperature is reached, D08...
View ArticleRostock Mini Pro , motors do not run (1 reply)
Hello everyone, I started in Rostock Pro Mini kit , I finished the mechanical part successfully, but I have some problems with the electrical part . I followed the sitemap 3DPrinterCzar for the...
View ArticleRepetier V1.04 object placement co-ords (no replies)
Hi I have just upgraded to v1.04 and am puzzled as I no longer seem to be able to enter co-ordination on object placement as the translation field is no longer visible. is this still availble somehow?...
View ArticleRepetier-Host V1.0.4 extruder calibration (no replies)
Hi Guys, I just tried the new version of RH and I am having some issues with the extruder calibration. Perviously, I used .85b version and the extrusion was off by 2mm which I adjusted with no...
View ArticleRepetier Host for OSX - Dead? (1 reply)
I've been waiting for an OSX update for Repetier for a while now, but am not seeing anything being released. Are there any plans to bring Repetier for OSX up to speed with its windows counterpart? My...
View ArticleRepetier V1.04 2nd extruder Temp reading (no replies)
Hi The temp reading for extruder 2 always shows 100c whether active or inactive. When I disconnect and reconnect with Ver 0.95F I do get a reading on the second extruder, although I have to make it...
View ArticleHoming speed (1 reply)
I was doing a few modifications to my OrdBot today (basically a RepRap). I use Repetier firmware as well as Repetier Host. It has been working well but since I made a a few changes to the settings the...
View ArticleProblems with auto leveling, i3 (no replies)
Hi. I'm trying auto bed leveling on my prusa i3 running Repetier firmware. I have an inductive sensor mounted, and calibrated according to the hotend nozzle, with an aluminium heatbed. When i try to...
View ArticleDefault setting for second Extruder 100C (no replies)
In printersettings you can set the default temperature setting for Extruder1 (current Extruder), but the default setting for extruder 2 (if enabled) is now hardwired to 100 deg C which is not a good...
View ArticleDuration print time info (5 replies)
Hi all, I'm using repetier firmware and I need the duration print time on my display during print execution, but I don't know how to get the info from the gcode (i suppose that it could be present...
View ArticlePrint time error (1 reply)
I have noticed a printing time error on several recent projects. Perhaps I have just not noticed before. One project took about 1 hour longer to print than the G-code file's ppredicted ~3 hours....
View ArticlePrintersettings z max size has changed behaveour in RH (3 replies)
In earlier releases i think that z max size (printer height) in printer settings was overruling settings in firmware so if you changed printer settings you could trim printer z max height from RH. Is...
View Article