repetier compatibility with Android/WindowsRT (1 reply)
Dear all, does anyone know if repetier-host is compatible with Android or WindowsRT? I was thinking to buy a tablet or small notebook to drive the 3D printer. Any experience? cheers
View ArticleZ-Leveling doesn't quite work (1 reply)
I'm trying to set up Z-probing/bed leveling on a delta printer, and I'm having a bit of an issue: when i give the G30 command, the head zips down at what I think is full speed (it's more than either...
View ArticleClik here to view.
hole dia not matching the .stl file info (2 replies)
I'm having a little trouble with hole dia not matching the .stl file info on the print. Could I be missing a setting someplace? Before I printed this part I printed out a 100 millimeter Square pattern...
View ArticlePin designations question (4 replies)
On the Repetier firmware, waht do the pins in pins.h and uiconfig.h refer to? for example, in the following, what are pins 54, 55 & 39 in the pins.h for a Ramps 1.3 board? #define X_STEP_PIN 54...
View Articleanyone managed to get repetierhost running on a arm7 or rpi? (no replies)
I'm having issues getting it running. I am tryin to run it on a udoo. Quadcore Armv7 based cpu.. it crashes/segfaults. please give me advice/hints.
View ArticleProblem with homing, endstops and repetierhost:S (1 reply)
Hello, I am currently finishing my 3D delta printer, modeled along the lines of the original Rostock. I am running into some very strange problems and I am not sure how to fix them. They are driving...
View ArticleRapetier has stop to run on 64Bit Win 7 (no replies)
Hi, After installed Repetier-Host Windows 0.90C on my laptop, it stop working and can't enter the software interface. I also try Repetier-Host Windows 0.84, it also has same problem. Here is my PC...
View ArticleCalibration issue (3 replies)
Hi, I am seeing inconsistent dimension inaccuracies between prints. On a gear wheel I have a discrepancy of about 10% between x and y, while on a calibration cube, I only see about 3%. I have double...
View ArticleCompiling problem with Z_MAX_Endstop not used in nw firmwareversion 0.90 (no...
DEar Repetier, If have a Mendelmax 1.5 with electronic of G3D. I have update your last develoment of the Firmware and copied the Arduino AVR / repetier directory over the existibg repetier-directory....
View Articlesolved-problem with 200K thermistor (no replies)
Hi, I have a 200K thermistor on my heated bed and a 100K on my hotend. My problem is that when set to read the 200K in the firmware, the host gets a steady reading of 0C. If I set it to a different...
View Articleissues with slic3r 1.0.0RC1 (1 reply)
Hi there, I have some issues with the new version of slic3r. One issue is that it often crashes while it is slicing. I "installed" it in the repetier-host folder by replacing the previous version...
View Articlefixing filament problems while printing (no replies)
Hello, I would like to suggest a new feature to correct print errors. I've had many prints that for whatever reason the filament does not stick to the previous layer, and separates in the middle of a...
View ArticleRepetier Firmware: Dual Y Steppers (2 replies)
Hello! While not a question about Repetier Host (which is working great for me), I hope that you might be able to help me with a Firmware question, or at least guide me to how I could start to modify...
View Articlecannot see Ramps SD card with Repetier firmware (no replies)
I am trying to get an sdramps adaptor running with Repetier firmware. Although the card can be seen if I load the sdrampstest to the Arduino, if I compile and upload Repetier firmware I get garbage -...
View Articlepid autotune bed failed (1 reply)
hi, i'm finishing my first self made prusa and i'm at the PID autotune point of the build.. Ive managed to autotune the extruder, which now gives me a nice oscillation of 1 degree, but the bed temp is...
View Articleslicing comes out with unwanted blocking (1 reply)
hello I am sending all my files to netfab, and then opening in repetier, slicing, and very dissapointed to see somehow the slicing has dumbed down my design, example where we have a smooth surface, it...
View ArticleUI click encoder problem (1 reply)
When I connected up my LCD and encoder/clickswitch to my Ramps board the display was cycling through a number of menu entries, speeding up rapidly to a blur. Turning the encoder slowed it down...
View ArticleRepetier Host for Mac crashes repeatingly (no replies)
We are running a single extruder Creatr on a Macbook, but Repetier-Host crashes continously (about 20 seconds after the printing started). Setup was fine, STL loading is fine, Slicing is fine, heating...
View ArticleFirst layer gap adjustment while printing. (no replies)
Hi. Im not sure if the developers read this forum but I have a couple of suggestions. I have two separate printers and the critical first layer gap often varies on both. I guess it’s the limitation of...
View Article/ #define CASE_LIGHTS_PIN -1 (2 replies)
have a ring let under my effector I want to use a digital pin to turn on my light I now use the Pin D6 card Azteeg X3 Use the command G-code M42 P6 S180 to activate there a possibility other than...
View Article