Bed height while printing / extruder calibration (no replies)
Hi, I am trying to slice with the built in Slic3r. I have configured everything I can see applies. When I print the, everything homes OK, but the bed then comes up 50mm below the extruder. The host...
View ArticleFeature request (2 replies)
Is there any possibility to have a script or any commands executed automatically after connecting to printer. I could need a G28 command issued after connecting, so printer is calibrated from start as...
View ArticleWish for Repetier Host (PlugIns/AddOns/Interface) (no replies)
I have a Megatronics v2.0 Board. Now i want to use one Temp Sensor to check the Case Temp. Can you add something to use AddOns/PlugIns for more functions or a Interface to use the Data in a extra...
View ArticleLosing home (especially Z Axis) (1 reply)
So, I've tried to move to Repetier Host, and I really like the Interface, but I've got Issues with homing. At startup the Printer homes nicely, goes to every endstop, moves back a few mm and goes...
View ArticleBulging cube - too much filament? (no replies)
Hi, My first printed object was a flat keyfob, which came out not too bad, so now I'm trying a 1cm cube. The dimensions are not too bad, but there is some bulging at the sides, and it's just short of...
View ArticleRepetier 0.90 Delta Printer problem with homing (8 replies)
Hi, i have a problem with my Kossel, i have mechanical endstops pluged on a Axteeg x3 Rev. 1.12 with Viki LCD. My problem is that when i use G28 the axis go home, ok the axis go 20mm down, ok X is...
View ArticleSetting up firmware for fishing line spools (no replies)
Hello, I've searched for fishing line spool system setup and while I've found a few that show how to do it mechanically, I haven't found things that show how its done whitin the firmware. So my spool...
View ArticleRepetierHost 0.90D Linux hangs on some SD Card Manager operations (no replies)
Hi, I have installed RepetierHost 0.90D Linux on my fedora 19 system and am communicating with nophead's Marlin on a Mendel90 at 115200bps. In the limited testing I have done so far everything appears...
View ArticleY offset each layer only with Repetier Host for Mac (4 replies)
Hi, thats me again. After i have fix the problem with the endstops with your help i have the next problem. I´m using the Repetier Host 0.56 for Mac and in each layer i have a offset in Y direction. I...
View ArticleMoving Repetier between computers (1 reply)
Hi, I'm trying to move repetier between computers without having to re setup all the config information about my printer. Does anyone know if that is possible? Thanks, Max
View ArticleFeature request (3 replies)
When you start a new print you may ask fw to set temperatures and wait for this (M109,M190 etc). It would be nice if these commands were cancellable without powerdown,reset or similar. If params for...
View ArticlePrint fails on same layer (no replies)
I have just had two prints stop at the same layer, along with another that failed in a similar manner. In each case the print had simply stopped, but commnuncation seemed to be intact as I was able to...
View ArticleDisplacement in y axis mid print (4 replies)
Hi, Everything seems to be working well, except that when trying to print a calibration cube, I get a strange displacement in the y axis halfway through. It happens each time, resulting in a step like...
View ArticleWindows connection issue (no replies)
Hi, Trying from a windows laptop because linux isn't working for me. I feel I must be being stupid, but I have searched about and can't find the answer. I don't have any com10. I'm connecting to an...
View ArticleSlic3r profiles being ignored with repetier .90d on Ubuntu (no replies)
When I do a slice with slic3r in repertoire-host the default profile is used instead of the chosen profiles. I saw this was a problem in previous versions, but was supposed to be fixed in .90d. Any...
View ArticleStrange home values on delta (3 replies)
When I use Repetier Host manual control to zero all axis, I get Z=326, X=-135, Y=-135. If I advance the head from the stop position by using the positional control to advance say 50mm down and then...
View ArticleHelp with E0 pins.h (no replies)
Hi, I'm sorry if there is another thread on this but I can't seem to find the info I'm looking for. I'm having troubles getting my extruder (E0) to work with a delta configuration. I;ve already had to...
View ArticleCan't turn on extruder heater (2 replies)
I know this is a common problem, and there are plenty of resources already out there, but for the life of me, I can't figure out what's wrong. The extruder resistor is plugged into the right pins,...
View ArticleNevermind. X( (no replies)
nvm. hehe We don't know how to delete this. MODERATOR. YO. TAKE THIS DOWN. X( ;) B) :)-D Our problem was that the extruder wasn't running. We faked it out with the thermistor. It has to be under the...
View ArticleRepetier with max6675 on ramps 1.4 (no replies)
Good Morning, I'm new to this forum and I hope to make this post in the right place :-) . I'm building a 3d printer and I like the composition Arduino Mega 2560 + Ramps 1.4 + max6675 because I have an...
View Article