Reading time for tooltips (no replies)
RE Repetier Host, Is it possible to make the tooltips stay on until mouse pointer no longer hovers over it? IE, just get rid of the timeout???? I can't read (that's about 5 sec worth)...................
View ArticleRepetier Server on an OrangePi Zero?? (1 reply)
Well I can confirm it works... that may not be much of a surprise to those well versed in linux but it was a bit of a surprise to me..... Up to three printers connect via USB to the Pi Zero which is...
View ArticleWill not print (7 replies)
Hello to all at repetier, I had some trouble trying to connect my printer to my computer, but you put me on the right track, and it is connecting beautifully now, however I now have another problem,...
View ArticleFan comes on during extrusion after print (2 replies)
OK, I have a MKS 1.5 board, which is supposed to be a combination Arduino/Ramps board on a delta printer. The board has a non-controllable, always on 24 volt outlet which is used by the cold end fan...
View ArticleJam detection configuration - help please (1 reply)
Does anyone have a link to a step-by-step guide to configuring jam detection on Repetier, or have any suggestions to help, please? I am using Repetier Host v2.0.0, Server v0.80.3 and firmware v0.92.9...
View ArticleRepetier Host and Marlin firmware Compatible? (1 reply)
Hi all, I've just set up my new 3D printer (helloBEEprusa Serial 1111500275-to-X). The machine works fine itself, but I am finding it impossible to connect it with Repetier-Host software. The firmware...
View ArticleLayer detection (6 replies)
My repetier host excactly knows which layer is printed. It says so at the bottom : Layer n / nn However, when I look into the Gcode, I can see z-axis positioning but that is not the same as layer...
View ArticleTemperature setting not staying set (1 reply)
Im slicing in Slic3r and the set temperatures are not staying set when i run the G-code in Repetier-Server. Is there a setting in RepetierServer that will enable this or is the issue in Slic3r?
View Article'SD init fail' on Repetier 0.92.9 (1 reply)
Hello guys, I have been wrecking my brain all weekend over this and cannot get my printer to work. I have just recently updated my firmware from a very old version (not sure of the number but it was...
View ArticleUnable to run Repetier-Host (3 replies)
Good day, everyone! Please give me a hand here:) I cannot run Repetier-host neither from the terminal, nor via the desktop configuration file. What do I do? This is what I keep getting: Could not set...
View Articlemultiple gcodes in a row which get printed after each other (1 reply)
I use the repetier host software it is nice and easy to work with! is there a possibility like a plugin or something like that for series print ? Like a list with multiple gcodes in a row which get...
View ArticleCura 2.6.2 Baidu scanner gives warning "Win32.Trojan.WisdomEyes..." (1 reply)
Hi there, excuse me if this isn't the right place to ask this, but I couldn't find any better. Pls show me, if there is. I'm using Cura 15.01 that came with my Repetier-package. I'm trying to use...
View Articletool change repetier (1 reply)
Hi, After few days of recherche I need some help. I would like the printer applies a different tool change gcode when it passes from the head 1 to the head 2 and from the head 2 to the head 1. I tried...
View Articlex axis ramdomly decides up is down (6 replies)
I am working with a homebuilt delta printer. Using ramps 1.4 on arduino mega for controls. Here's the problem. Sometimes the x axis decides that to move the carriage up it needs to go down. I am using...
View ArticleModel View Lighting (1 reply)
Hey everyone, So I can't figure out the lighting setup in the model preferences settings. There are 4 lights you can turn on and I can't figure out what xyz coordinates to put in for any of them. I...
View ArticleInvalid Extruder message (no replies)
I'm using Repetier-Host V2.0.5 I'm trying to set up the extrusion length setting on extruders 2 and 3. When I do I get the following message: echo: M92 Invalid Extruder 2 echo: Settings Stored (405...
View ArticleI'm having a problem getting stepper motors 1 &2 to eject the proper amount...
I am using Repetier Host V2.0.5 along with Marlin RC8 on a Rumba board. #1 Extruder steppers 1 & 2 always eject the same amount of filament even though I do change the Default_Axis_Steps_Per_Unit...
View ArticleHow can I disable the "Heater Decoupled" feature (no replies)
As the title. I develop my own hotends with my own heaters and it is getting in the way of characterizing the behavior of the hotends. Mike
View Articlefeature request (no replies)
Hey Repetier, would it be possible ,without too much trouble, to change the font color in the g-code to highlight certain commands? For example all Z commands Z17.7 in red, etc. This could make it...
View ArticleRamps and Hot End on D8 (no replies)
Using Ramps 1.4 with repetier firmware and for some reason the hot end heater using D10 is somehow not working on that pin but works on D8 . It works ok there but schematics all show it on D10. Should...
View Article