Layer detection (no replies)
My repetier host excactly knows which layer is printed. It says so at the bottom : Layer n / nn However, when I look into the Gcode, I can see z-axis positioning but that is not the same as layer...
View ArticleTemperature setting not staying set (1 reply)
Im slicing in Slic3r and the set temperatures are not staying set when i run the G-code in Repetier-Server. Is there a setting in RepetierServer that will enable this or is the issue in Slic3r?
View Article'SD init fail' on Repetier 0.92.9 (no replies)
Hello guys, I have been wrecking my brain all weekend over this and cannot get my printer to work. I have just recently updated my firmware from a very old version (not sure of the number but it was...
View ArticleUnable to run Repetier-Host (no replies)
Good day, everyone! Please give me a hand here:) I cannot run Repetier-host neither from the terminal, nor via the desktop configuration file. What do I do? This is what I keep getting: Could not set...
View Articlemultiple gcodes in a row which get printed after each other (1 reply)
I use the repetier host software it is nice and easy to work with! is there a possibility like a plugin or something like that for series print ? Like a list with multiple gcodes in a row which get...
View ArticleCura 2.6.2 Baidu scanner gives warning "Win32.Trojan.WisdomEyes..." (1 reply)
Hi there, excuse me if this isn't the right place to ask this, but I couldn't find any better. Pls show me, if there is. I'm using Cura 15.01 that came with my Repetier-package. I'm trying to use...
View Articletool change repetier (no replies)
Hi, After few days of recherche I need some help. I would like the printer applies a different tool change gcode when it passes from the head 1 to the head 2 and from the head 2 to the head 1. I tried...
View Articlex axis ramdomly decides up is down (1 reply)
I am working with a homebuilt delta printer. Using ramps 1.4 on arduino mega for controls. Here's the problem. Sometimes the x axis decides that to move the carriage up it needs to go down. I am using...
View ArticleModel View Lighting (no replies)
Hey everyone, So I can't figure out the lighting setup in the model preferences settings. There are 4 lights you can turn on and I can't figure out what xyz coordinates to put in for any of them. I...
View ArticleInvalid Extruder message (no replies)
I'm using Repetier-Host V2.0.5 I'm trying to set up the extrusion length setting on extruders 2 and 3. When I do I get the following message: echo: M92 Invalid Extruder 2 echo: Settings Stored (405...
View ArticleHow can I disable the "Heater Decoupled" feature (no replies)
As the title. I develop my own hotends with my own heaters and it is getting in the way of characterizing the behavior of the hotends. Mike
View Articlefeature request (no replies)
Hey Repetier, would it be possible ,without too much trouble, to change the font color in the g-code to highlight certain commands? For example all Z commands Z17.7 in red, etc. This could make it...
View ArticleRamps and Hot End on D8 (no replies)
Using Ramps 1.4 with repetier firmware and for some reason the hot end heater using D10 is somehow not working on that pin but works on D8 . It works ok there but schematics all show it on D10. Should...
View ArticleUploading Firmware to Prusa I3 type priner (1 reply)
I am well behind the curve on these things - call me a preemie-newbie. In order to load the firmware does the board have ot be connected to all of the pieces like motors heaters, SD card reader,etc.?...
View ArticleAnet A8 V1.0 board (no replies)
Yes, I have the square red V1.0 Anet board for my A8. I looked in the configuration.h file and see that servo control is listed. My question is does the board actually support servo input/output?...
View Articleg-code in printer tab (3 replies)
Can anybody tell me where I get the values to enter into "G-CODE" on the print panel tab please? I have a Mac trying to connect with a Tronxy XY-100 printer. many thanks in anticipation. Colin
View ArticleProximity Sensor for Z End Stop (3 replies)
I have a Rambo that I'm changing end stops on. Right now I have a mechanical y stop, opto x and I'm trying to set up a LJ12A3-4-Z/BY orange tip proximity sensor for Z min. X and Y work fine. When I...
View ArticleTemperature Export in Repetier Host (no replies)
I am using a heater in my setup and am wondering how do I export the temperature data into excel?
View Article3 point Z Probe issue (1 reply)
Hi Looking for some help. I have an HE3D, having got the correct firmware loaded and everything moving in the correct direction, when I go to Print and the Auto level start to do it thing the Z-Probe...
View Article:S Repetier Server Suddenly acting odd (no replies)
Running latest Repetier Server on Raspi3. First model I sliced and uploaded is the Rook (and it printed perfectly) -- the one that you can see the render is showing the complete model. Ever since...
View Article