@pause in sender (2 replies)
I am using repetier-fw with repetier-host, and btw ty for both. Everything is fine, except me being not normal, that being said i need two pauses in g-code. The "@pause" works very nice for the...
View ArticleFeature request:Use repetier with Slic3r.pl instead executable version...
I made this batch: C:\dev\CitrusPerl\bin\perl C:\Users\Luca\Documents\GitHub\slic3r\Slic3r-master\slic3r.pl the result is, when I click the "configure" menu evrything is ok, slic3r open its windows,...
View Articlerepetier +megatronics + thermocouple k-type (3 replies)
hallo ik ben eelko en ik heb een hulp verzoek ik heb een reprap prusa gebouwt en ben al een heel eind ik heb problemen met de temp sensor voor de kop gebuik ik een 100k thermistor werkt zeer goed voor...
View ArticleRepetier 3D View mangles KISSlicer g-code (1 reply)
So, I'm slicing the following model for a 0.20 mm nozzle in KISSlicer and trying out Repetier for the first time to visualize the g-code. I've been using Pronterface to inspect the g-code before...
View Articleuiconfig.h (1 reply)
Why the pin numers are hardwired inside UICONFIG.H ? I mean: #define UI_DISPLAY_RS_PIN _BV(4) #define UI_DISPLAY_RW_PIN _BV(5) #define UI_DISPLAY_ENABLE_PIN _BV(6) #define UI_DISPLAY_D0_PIN _BV(0)...
View ArticleRepetier host issues + lock up (no replies)
Found two problems: 1) It is possible to config "zero extruders", but software then locks up and dosen't run anymore. Solved changing (regedit) register value. 2) On a multiple extruder board...
View Articlealtering print speed (4 replies)
I am having difficulty altering print speed. I have set max speed in firmware but when I try to alter print speeds in slicer settings its does not make a difference. How else can I change the speed if...
View ArticleM300 gcode support - beeping wanted (2 replies)
Feature Request: I remotely administer my 3d printer (tweaked Prusa Mendel) running Repetier. Often a print job finishes/fails and the machine is in need of human assistance before it can do anything...
View ArticleCopy object generates imperfect plates (3 replies)
I sliced and printed an object that was cloned/copied in Repetier host. It was a thin wall object that was printed 4 times on the same plate. 2 of the objects came out with 2 perimeters and 2 objects...
View ArticleRepetier can't change parameters (3 replies)
Printer = Rostock, Repetier Firmware = 0.81 Board = Arduino Mega2560/Ramps1.4 Computer = Windows XP (also Ubuntu) Arduino = 1.0.3 on windows and 1.0.4 on Ubuntu I have got as far as getting all axis...
View ArticleFeature request: OPS speed (no replies)
Is it possible to add a setting for speed used during retraction when using OPS?
View Articleuiconfig sets about keys (4 replies)
Repetier, Hello! I get lost in the button configuration (uiconfig.h). I want to map the pin to my hardware, how to set up it?( Hardware:GEN7+I2C BUS+ MCP23017 PB0-PB7 connection with eight buttons)...
View Articlehow does the software repetier calculate the checksum (1 reply)
Hi everybody I am facing a problem. I can generate de g code but I can´t recognize the checksum number We are using PIC but we can´t calculate the checksum number As we are developing a graduate work...
View ArticleGen7 V1.5-20MHz-Repetier firmware-communication problem (no replies)
In the past few days, I test a variety of communication rate stability in the GEN7 V1.5 in my machine (9600,19200,38400,57600,56000,76800,111112,115200,250000). By eight or more tests, I discovered a...
View Articlerepetier firmware 0.81 GEN7 1.5 : Z axis problem (no replies)
Hi all, i'm new to this forum and to the reprap world... my intention is to build a delta "rostock like". concerning the electronic part, I've just built and successfully tested a GEN7 1.5 board from...
View ArticleGen 6 board, setup issues (1 reply)
ive compiled and uploaded the repetier firmware for my Gen6 but when i run the host and connect to the printer it doesnt seem to actually be connected, under printer info it says unknown type and...
View ArticleRepetier Host Skeinforge No visualisation Gcode (no replies)
Hello, It seems I'm the first with this problem. When I slice with Skeinforge, slicing and Gcode are Ok but I can't visualise the result like with Slic3r It asked me to download Tkinter. I try...
View ArticlePID Autotune error (1 reply)
I have had my heated bed tuned for 60 degrees for PLA. Today I tried to tune it to 115 degrees for ABS. It ran for about 12 minutes and then gave me a PID Autotune Failed. Temperature too high. What...
View ArticleRepetier - Temperature Curve (1 reply)
Just a quick question - the lower graph of the Temperature Curve, what does it represent? I know its a bit of a dumb question but I haven't been able to find it otherwise! Cheers :)
View Article0.85b Sanguino Connection Time (2 replies)
I just tried the new 0.85b and it seems the connection time improved a lot. The previous version took around 7-8 seconds to connect to my Sanguinos with 644p and now it's instant. Is it just a placebo...
View Article