1.00 Beta 1 + Cura cooling (no replies)
Hello. CuraEngine plugin calculates "fanFullOnLayerNr" parameter wrong - it always 0 In CuraEngine.dll CuraEngine.CuraEngineInstance.WriteCuraConfig there is line with "fanFullOnLayerNr" parameter...
View ArticleWhere did flowrate go? (4 replies)
I just installed the 1.0 beta. I haven't changed my slic3r settings, but it appears to be extruding too much filament. I usually would adjust the flowrate slider, but I can't find it anywhere. What...
View ArticleRepetier-host v1.0 RC1 for windows (1 reply)
Hi Maybe it is late. But, where is the button/command for 'Heat On' Trying to setup Printrbot simple
View ArticleRepetier Host 0.95F broke somthing (1 reply)
I was using it and did a few prints then when removing a file in the placement mode it closed itself. After restarting the program after a reboot it still does not work and I get the following...
View ArticleRepHost crashing when plating/inspecting/printing large objects (4 replies)
Win 7x64, 8Gb 1600mhz RAM, SSD = main hard drive. RepHost is the ONLY software open at the time of this occurring. Basically any time I plate and then attempt to slice/print a large object, RepHost...
View ArticleV1.00 Beta Manual Control input for x/y z and extruder (2 replies)
I really like the new look and controls of the new V1.00 but would like to be able to input my values as some times the defaults don't always meet the need. Any chance that you could throw a key-in...
View ArticleRepetierHost 1 RC2 - Disappearing hotbed control - Solved (1 reply)
I am having a strange problem since installing the latest host software. The hotbed heater control disappears when the program connects to the printer and it's stays like that until I close and reopen...
View ArticleUnable to find nozzle diameter settings for Cura engine in R-H V1.00 RC (2...
Hello, maybe I am just blind, but where do you configure the nozzle diameter for the new cura slicer? Thanks
View ArticleRepetier Host Beta 1 configure park position (no replies)
I love beta 1 of Repetier Host and am looking forward to the final release. How do I configure the park button to move the printhead to y max rather than y min?
View ArticleRepetier-Host V1.00 RC2 Remarks (no replies)
Hello, I am trying the new Repetier-Host V1.00 RC2 and I found three small thing that need attention. 1- In the "Manual Control", the X, Y, Z, coordinate are not align in the box for them and they are...
View ArticleImporting .ini settings? (1 reply)
I have a few improved .ini settings for slic3r that I want to use. When I try to add it to my list in the program, I get the error "The selected preset does not exist anymore" and then the prompt...
View ArticleProblem moving x, y, z motors in Manual Control (no replies)
I'm trying to control my own cartesian-design robot using a stock Printrboard (Rev D) (from Printrbot flashed for a Printrbot Jr.) with RepetierHost (V0.95F). I connect OK and can jog (move in tiny...
View ArticleMegatronics v2 third extruder (no replies)
So I have been working on setting up a third extruder on my spiderbot. I managed to fry part of one of my megatronics boards when I turned up the stepper current too high. I found part of my problem,...
View ArticleZ probe configuration for auto level (no replies)
Has anybody here implemented the bed auto level (z probe) feature on Repetier firmware for a cartesian printer? I'm not sure how to set up the configuration.h file for this, even after reading the...
View ArticleSerial com error (no replies)
Hi, I bought a new 3D printer cant get any support from the supplier. after I setup Repetier V0.90C and connect to the 3D printer. There is error message as following: "Serial com error:...
View ArticleRepetier firmware: how do change the thermistor type? (no replies)
Hi, I have downloaded a configured version of .91 from the website and it compiles fine, I can move all the axis, turn heaters on/off etc. I need to change the Thermistor type: I have constructed a...
View ArticleRepetier Host Beta 1: Using Cura plugins (1 reply)
Hi! Just wondering, can I somehow use Cura plugins when using CuraEngine in Repetier Host? I had some difficulties with my delta printer and magnetic joints, when they started to detach when nozzle...
View ArticleRepetier 1.0 RC2 super slow z axis on print starts (2 replies)
Any way to speed up the z axis on deltas (not sure if it effects cartesians)? There are 3 times where it just runs insanely slow. If you manually move the Z axis, start a print, or pause/restart a...
View Articleconfig tool set NUM_EXTRUDER to 0? (2 replies)
I downloaded the latest firmware, 0.91, and tried the config tool as I downloaded to set things up for me. Things are going ok, and I am even trying the host ver 1.0 RC2. My extruder will not heat or...
View ArticleInfill Settings in Cura (2 replies)
Can anyone tell me where the infill settings are in the Cura slicer in RepetierHost. I downloaded the standalone program to see if it was evident in that version and it's quite obvious where to change...
View Article