Mega2560+Ramps1.4+ Max6675+Repetier Firmware V0.82.2 compile error (1 reply)
Hi all , i use mega 2560 + ramps 1.4 and trying to use max6675 for extruder temp. When i set extruder sensor type to 101 (MAX6675) it generate compiling error ;"Extruder.cpp:221: error: expected...
View ArticleFilament Feed Rate (6 replies)
I must be blind as i can't seem to find where to change /cal the filament feed rate. Where is this done in Repetier software? Help appreciated.
View ArticleComm hang on Mac (Mountain Lion, 0.56) (2 replies)
Hi, I upgraded to Repetier-Host Mac 0.56 recently, but it seems it doesn't like my printer... After "connect", all communications just hangs, and nothing happens in the log window. Downgrading to 0.53...
View ArticleHeatbed start heating then stop (4 replies)
Hi, I'm using a generic PCB Heatbed on my Prusa Mendel v2 (with ramps 1.4) but I have some troubles with it. When I run the heater (from Repetier, option "Heat Printbed", target = 60°C), the bed...
View ArticleEditing custom skeinforge profiles (2 replies)
Hello, I'm trying to load custom skeinforge profiles in Repetier-Host 0.85b. I can add a folder to .skeinforge/profiles/extrusion, and it shows up in the list of profiles, but when I click on...
View ArticleCommutation protocol (2 replies)
Hello all, I am trying to program my own microcontroller that will work with Repetier. I am using Parallax’s Propeller (Prop) to learn on, and to make something I think is really cool. But I am having...
View ArticlePerimeter speeds (3 replies)
I am having problems with the perimeter speeds on my Rostock printer using Slicer running under Repetier. Perimeter speeds on a hollow shell, the Tiki statue by Cerberus333 I get an outer perimeter...
View ArticleRepetier Host homing question (2 replies)
Hi all, Home button work after startup printer . X home , Y home or Z home works everytime . When pushing home after startup then doing something on printer (shift extruder by hand, fixing someting...
View ArticleStrange motor problem (4 replies)
Hi, I'm using an Azteeg X3 controller with repetier firmware and I have a strange motor behaviour. When motors are disabled, the first move on the Y axis often generated a short noise ("CLAC') when it...
View Articleheater,thermistor not work (4 replies)
Repetier, hi, I am using Lambo board, honeywell thermistor. I had built my 3d printer 1 month ago, but i can't operate it until now. I have uploaded Repetier firmware, but x,y,z axis work correctly...
View ArticleRepetier, Gen7 1.5 and the heating bed (5 replies)
Hello everybody, after today I printed the first time successfully with a Prusa Mendel, Gen7 v1.5 board and the repetier firmware, I would like connect the heating bed to the Gen7 v1.5 PCB make it...
View Articlegeneration 7 v 1.5 thermistor pins (1 reply)
hello my name is Charles, I would like to point out an error in the firmware repetier 0.82, which concerns the generation 7 v 1.5 card, called 71 in the firmware, since in repetier host I do not read...
View ArticleMachine pause (7 replies)
Is it possible to link one input pin to IMMEDIATE pause/restart of printing job (not waiting for the cache to be emptied) ? Thank you! Davide
View ArticleSetup heat bed and extruder (no replies)
Hello :) Can anyone help me? I'm having trouble setting up my heat bed and extruder settings in my repetier firmware. I have 100k resistors on both heaters but the configuration setup is really...
View ArticleNo homing G28 / ignores endstops (2 replies)
Hi there! I new to 3D printing. I've build a Rostok. Mechanics and electronics seems fine (Gen 7 1.5). Repetier firmware 0.83 / Repetierhost 0.85c. I successfully flashed the fimware to the board and...
View ArticleFirmware Ramps 1.4 with funduino. (no replies)
Hello everyone. I just finished assembling my RepRap. I started the calibration procedure. Two concerns: Run my card Arduino Mega 2560 WITH MY RAMPS 1.4 Go to the Z axis once in contact with...
View Articlerepetier firmware proposal for delta endstop offset calibration (1 reply)
Hi all and mainly Repetier ;-) I've recently built a delta printer running perfectly fine under repetier host + repetier firmware (see [groups.google.com]), so first of all many thanks for those two...
View ArticleRepetier-Rostock (no replies)
Setting up my classic Rostock with repetier host and firmware. have it to the point where it will home - but thats it- when i move x, y z it moves like 50 mm instead of 1. Extruder wont move. Hot end...
View ArticleRepetier-Host 085b issue ? (1 reply)
Dear RepRapers, i have an strange behaviour of newest repetier-host software running on my win7 pc. I wonder whether it is maybe a issue of the newest release i installed a few days before. I have...
View ArticleZ-Axis Problem (no replies)
Hello, I am having unugual problem running latest rapetier firmware and software. When I configured Step/mm and check move for all Axis to any dirrection it is no problem. I have RAMPS 1.4 with Smart...
View Article