Spiral Vase / get step over (no replies)
I'm sure you have answer this question before but I have selected (Spiral Vase ) in slicer 3r . But no matter what I do I still get step over at the same place on every revolution of the print.
View ArticleRepetier-Host Mac 0.56 crashing when connecting to printer (1 reply)
I've been running my Marlin/Ramps 1.4 based delta printer with Repetier-Host 0.56 on Mac OS 10.10 and 10.9 with very few problems until last week, when it started crashing as soon as I click the...
View ArticleTesting with Repetier (1 reply)
Hello. I'm new with 3D Printing, and have built and calibrated a Prusa 3D reprap printer (so yes, I have those scars). However, my hotend has not yet arrived, and I would like to do a fake print using...
View ArticleRP loses heat bed control (1 reply)
I was printing and like a dummy I plugged in an Arduino via USB to program it and it killed my print. So I shut down RP and rebooted to start fresh print and when I try to connect to printer the...
View ArticlePins on Ramps1.4 (no replies)
I want to add a Fan. Generally I have problems to understand the link between the fields inside the configurator of Repetier und the Ramps 1.4 board. 1.In Repetier Configurator Fan Pin: "Heater 2...
View ArticleRepetier Host update of latest Slicer rev. (no replies)
What is a safe way of updating RP installation with latest slicer revision? This is related to Slic3R and Cura installation. I can copy Curaengine from Cura stand alone installation with assumed...
View ArticleRepetier firmware skipping first steps (1 reply)
When I run the attached short gcode program it skips the first approximately 50 steps but then carries on till the end correctly. The file is just to use the 3D printer as a pen plotter and mark out...
View ArticleRepetier v1.0.3 DRO display wrong (1 reply)
Problem with Z DRO display on manual screen when not homing axis and doing a G92 to manually set position. My Z home switch is broken so I can't home Z. Repitier Z DRO shows 0 in red at startup. In...
View Articleno slower feedrate possible (1 reply)
Hello everyone, I use the repetier host with the repetier firmware to controll my DIY-Laser/Plasmacutter. The Hardware ist an ArduinoMega and a RAMPS-Board. The slowest feedrate for Plasmacutting is...
View ArticleRepetier Auto Bed Leveling wont probe Z (1 reply)
i have attached my configuration file Z endstops have been disabled. Z probe trigger test on pin 63 is successful. (g31) i enter the G32 Command after my g28 x0 y0. Z probe arm lowers Extruder moves...
View ArticleMoving the head into z=0 position in the middle of the printing. (1 reply)
Hi, I'm just building my 3d printer. It is almost ready, it is under fine tuning. I'm using repetier host and firmware with Pibot controller card. In some cases it is doing a very strange thing....
View ArticleParking the head after every layer (1 reply)
Hi, I'm just building my 3d printer. I'm using Repetier with Pibot controller. It is in fine tuning phase. When I printing, the head it moving to the parking position (x and y axis) after each layer,...
View ArticleCan't run repetier on linux (2 replies)
Hello, I'm new here, just trying to get the software working, this looks like it might be the place where I can get help I just tried installing repetier, and whneever I try to run it I get the...
View ArticleQuick acces Buttons - Firmware question (1 reply)
I have 3 free pins on my electronic. I would like to add 3 buttons who will give me quick access to functions: 1 - home all axes 2 - move Z axis 10mm up and extrude 5mm of filament 3 - pause print Is...
View ArticleNew Repetier-Server released (no replies)
After a long time of development we finally released the first beta of the new Repetier-Server at http://www.repetier-server.com/. Compared to the last release it has a lot of new functions and...
View ArticleFresh install of RepetierHost 1.0.6 seems to affect 0.95 release (2 replies)
I have installed the latest RepetierHost release (1.0.6). It seems to work but has crashed after 10 minutes. Then I tried to use my 0.95 production installation (April 2014) ... but now it will no...
View ArticleSwitching outputs at defined temperatures (1 reply)
Hi, i'm using an Arduino Due and the RADDS v1.1. I've installed a led-bar at my printer. It has to be turned on if the temperature of one of the two heating parts is above 50°C. Is it possible to add...
View ArticleMelzi board (1 reply)
Hi All, I would need to solve 2 problems: - Z axis is moving only 1 direction. (I succeed to change the direction of the movement, but still the driver is rotating in 1 direction.) - Bed temperature...
View ArticleAdaFruit OLED display in Repetier Firmware (no replies)
I'm looking at building a display for my RepRap Wilson using an Adafruit OLED display. These tiny displays are very readable due to their high contrast. They use an SSD1306 controller that is...
View ArticleMarlin thermistor tables in Repetier (1 reply)
Is there a way to enter the Marlin thermistor tables into Repetier firmware from the web configuration page? I've been doing this by hand after the fact, but I'd like to be able to only have to do...
View Article